Free shipping Over €38

Dispatched within 48 hours

30-day easy returns

Black pivoting screwdriver with 16 bit types and the two storage holders
Right-angle head reaching the back of a drawer handle while the body lies flat inside the drawer
Pivot head shown in four locked positions: 0, 30, 60 and 90 degrees
Screwdriver in use on a frame, inside a metal box, and beside a panel
Rocker switch with a light press for 100 rpm and a full press for 180 rpm
  • Black pivoting screwdriver with 16 bit types and the two storage holders
  • Right-angle head reaching the back of a drawer handle while the body lies flat inside the drawer
  • Pivot head shown in four locked positions: 0, 30, 60 and 90 degrees
  • Screwdriver in use on a frame, inside a metal box, and beside a panel
  • Rocker switch with a light press for 100 rpm and a full press for 180 rpm
1 / 5

4-Angle Cordless Electric Screwdriver

  • 4 locking angles
  • 2 speeds · 5 torque settings
  • 16 bits included
€29,99 EUR
Налогът е включен Изчисляване на таксата за доставка при плащането
Color
Secure Checkout

Your payment information is protected by 256-bit encryption during checkout. We offer trusted payment options such as Apple Pay and Google Pay.

30-Day Money-Back Guarantee

Changed your mind? Return your item for a full refund under our 30-day money-back guarantee, no questions asked. Every order also includes shipping insurance for loss, theft, or damage in transit.

01 · Inside the drawer

Tighten the handle where a straight driver runs out of room.

A loose drawer pull can leave you with one hand on the handle and barely any space behind the screw. Set the head to 90° so the body can lie along the drawer while the bit meets the screw straight on.

9 mmBit centre to adjacent wall at 90°
78 mmMinimum working space in the illustrated 90° setup
Right-angle screwdriver behind a drawer handle
Diagram showing 9 millimetres from the bit centre to the wall alongside it

Measure the space first

Will it reach your screw?

9 mm
Measure sideways from the screw’s centre to the nearest wall. The 90° head is offset so the bit can run close to that wall.
78 mm
Measure along the screw’s direction, from the screw to the obstruction behind the tool. This is the minimum space in the illustrated 90° setup.

Check both measurements with the bit you plan to use. A longer bit needs more room along the screw’s direction.

The pivot head at 0, 30, 60 and 90 degrees

02 · Pick your approach

Four angles for four ways in.

0°
Go straight in on an exposed screw, such as a table leg fitting.
30°
Tip the handle slightly to clear the edge of a shelf.
60°
Move the handle farther aside when a frame blocks your grip.
90°
Keep the body alongside a surface inside a drawer or cabinet.

Check that the bit seats fully and the head is locked before driving.

03 · Around the house

For the little jobs that keep getting put off.

  • Flat-pack furniture: fit a hex bit to the fastener and drive it through the pre-drilled fitting.
  • Cabinet hardware: reach behind a handle or beside an internal panel.
  • Dim corners: the built-in LED lights the screw area so you can line up the bit.
Screwdriver used on a frame, inside a box, and next to a panel
Rocker switch light press and full press speed settings

04 · Start slow

Seat the screw before you speed up.

Press lightly for 100 rpm when starting a screw. Press fully for 180 rpm when the threads are engaged. Use the lower torque settings on small hardware and increase gradually if needed.

The LCD shows your selected torque and remaining battery level, so you can check both before you reach into the cabinet.

05 · Check your fasteners

What comes with the driver?

One rechargeable screwdriver, 16 bits in two storage holders (6 plus 10), and one USB-C charging cable.

Bits
PH1, PH2, PZ2; SL3, SL5; H2.5, H3, H4, H5; T10H, T15H, T20H, T25H, T30H; S1, S2
Head positions
0°, 30°, 60°, 90°
Torque settings
0.5, 1, 2, 3 and 4 N·m
Speed
100 rpm (light press); 180 rpm (full press)
Charging
USB-C; 2,000 mAh rechargeable battery
Display & light
LCD for torque and battery level; LED work light

First time out of the box

Match the bit. Lock the head. Start gently.

  1. Match the fastener

    Pick a bit that fills the screw head without wobbling. Keep the other bits in their holders.

  2. Choose an angle

    Choose a locked position that lets the bit meet the screw squarely and leaves room for your hand.

  3. Use a light press

    Start at 100 rpm and a low torque setting. Increase torque gradually if the screw needs it.

Before you choose

Will it fit my narrow space?

Check both directions: the 9 mm measurement is from the centre of the bit to the nearby wall. The 78 mm measurement describes the illustrated working depth at 90°. The bit you install and the shape of the space affect your clearance.

Can it drill holes?

It is a screwdriver for driving and removing screws. For drilling holes, use a drill and a bit made for the material.

What if I’m using it on a small screw?

Choose the bit that matches the screw, start at 0.5 N·m with a light press, and stop when the fitting is snug.

FAQ

When will my order ship?

Most orders ship within 48 hours of payment confirmation. We’ll email you a tracking number once your order ships.

Is my payment secure?

Yes. Your payment information is protected by 256-bit encryption during checkout.

What is your return and refund policy?

We offer a 30-day money-back guarantee. If you change your mind, you can return your item for a full refund, no questions asked. We’ll process your refund within 5–7 business days of receiving your return and issue it to your original payment method.

What if my package is lost, stolen, or damaged in transit?

Every order includes shipping insurance for loss, theft, or damage in transit. If there’s a problem with your delivery, email us at support@airasf.com and we’ll look into it. If your item arrives damaged, we’ll help arrange a replacement or refund.